DL SVL-1700M 微電腦立式雙中分軸鋁箔分切機

用途

該機被廣泛應用于雙零鋁箔、單零鋁箔鋁箔的分切、改切、抽條、復卷及雙張箔分卷等。

適用產品/業界應用：

鋁加工行業、食品箔、空調箔、家用箔、藥品箔、電池箔、電纜箔、電子箔、電容器箔等各種卷狀O態、H態純鋁箔。

主要技術特點

本機為雙收料軸之中心表面卷取、復卷；采用PLC控制系統，威綸10" 觸摸式熒屏， 四套日本安川伺服驅動器和安川伺服專用電機控制收放卷分切，收、放卷自動張力控制、到米自動減速停機、放卷到小卷徑自動減速停機、緊急停機時放卷不松料。雙收料軸分別由獨立伺服馬達帶自動張力控制,可同時收卷大小不同直徑；收料系統采用伺服系統控制,有高效率,高精度,低噪音等優點；主動力采用安川變頻器配合中國臺灣變頻馬達，由PLC系統控制；收卷可依卷徑和米數設定,到設定卷徑或米數時自動提前減速停機功能。兩條包膠主動軸是由獨立的動力傳動，配合收卷伺服馬達同步控制，當包膠中分軸外徑磨損時，只需上磨床磨掉磨損表面，直到包膠中分軸的包膠*磨損。也無需改變任何參數。分切采用圓刀及剃刀搭配，可針對不同厚度材料選擇不同刀具，分切寬度由鋁墊片任意調節，剃刀配合1mm間距的刀槽輥。該系統采用高可靠性電器元件、線路簡單便于維護、自動化程度高，操作簡便。

上料方式（可選擇）：1.收卷軸旋轉方式   2.有軸油壓自動方式   3. 無軸油壓自動頂錐夾緊方式

注：以上技術參數可根據客戶需求定制。

DL SL-1700MV MICROCOMPUTER VERTICAL DOUBLE SHAFT FOIL SLITTING MACHINE

Usage:

The machine is suitable for stripping and rewinding wide of light gauge foil and medium gauge foil etc.

Applicable Product / Industry Application:

Aluminum processing industry, food foil, air conditioner foil, household foil, medicine foil, battery foil, cable foil, electronic foil, capacitor foil and various kinds of roll shape aluminum foil of H states and O states.

Performance and Features:

This machine is a double feed axis center surface coiling, rewinding; adopt PLC control system, touch screen Weinview 10 '', 4 set Japan YASKAWA inverter servo drivers and YASKAWA servo motor to control the rewinding cutting, collect and release control automatic tension. When arrive the distance it will deceleration. Put the volume to a small winding diameter automatic deceleration, it will not lose material when in emergency stop. The double shaft respectively by independent servo motor with automatic tension control, and rolling with different diameters; Feeding system adopts servo system control, the advantage is high efficiency, high accuracy and low noise; The active force uses YASKAWA frequency converter and Taiwan Dolin frequency conversion motor and control by PLC system; Winding can be set according to the size of the volume and the meters to set the size of the volume or the number of meters automatically in advance to slow down. The two pack of the active axis is composed of an independent power drive, and the control of the servo motor, when the outer diameter of the rubber is worn out, is only worn out the wear surface in the grinding machine until the complete wear is broken. And also do not need to change any parameter. Cutting using a round knife and razor, it can be aimed at different thickness of material selection of different tools, the cutting width is adjusted by the aluminum spacer, and the razor is within the 1mm. By using high quality electrical components, simple circuit, well automatic, convenient for maintenance and simple for operation.

Material Installation (optional):   1. Unwinding shaft rotate mode

2. Hydraulic shaft automatic mode

3.Hydraulic clamping without shaft automatic mode

Note: The above technical parameters can be customized according to customer demand.